Compatibility: battery, solar and inverters with Camper Jarvis

Updated 16 October 2026Volty

Battery, solar charge controller, DC-DC charger, inverter, shore power: this page shows which energy devices you can read and control with Camper Jarvis. The list shows what already works today and what we are working on right now. It keeps growing, because we are constantly adding new devices.

As of October 2026

How to read the list

  • Supported: works today, you can use it straight away.
  • Beta: already works, but we are still testing and extending it.
  • In progress: the integration is being developed and cannot be used yet.

Most energy devices are read by Volty Pro. Volty Pro connects to your device through the manufacturer's data interface and sends the values wirelessly to the SmartKnob. There you see state of charge, solar yield and consumption together, even if your devices come from different manufacturers. More on this in Which devices Volty Pro can read.

Victron

Manufacturer Model/series Status Via What works
Victron MPPT solar charge controllers (BlueSolar, SmartSolar) with VE.Direct Supported Volty Pro (VE.Direct) Solar power, daily yield, charging stage
Victron SmartShunt, BMV-712 battery monitors Supported Volty Pro (VE.Direct) State of charge, voltage, current, time remaining
Victron Orion-Tr Smart, Orion XS DC-DC chargers Supported Volty Pro (VE.Direct) Charging power while driving, with the Orion XS also the emergency charge of the starter battery
Victron MultiPlus, MultiPlus-II, MultiPlus-C, Quattro inverter/chargers Supported Volty Pro (VE.Bus) Read values, choose the operating mode: on, off, charger only, inverter only
Victron Phoenix Smart Charger IP43 In progress Volty Pro (VE.Direct) The dashboard display is being built
Victron Phoenix inverters with data cable In progress Volty Pro On and off via the remote switch connector already works today, see below
Victron Cerbo GX In progress Volty Pro Next to a Cerbo GX, Volty Pro only reads along. Changing settings through both leads to conflicts.

A short note on VE.Bus: Victron does not officially approve third-party devices for its large inverter/chargers. Volty Pro is designed so that nothing should go wrong, but you still use the VE.Bus port at your own risk.

Votronic

Manufacturer Model/series Status Via What works
Votronic VBCS Triple, battery-to-battery chargers, DC-DC chargers, solar charge controllers Supported Volty Pro (RJ12 cable) Read values
Votronic Shunt in the VBCS Triple In progress Volty Pro This needs a new hardware version of Volty.
Votronic MobilPOWER SMI inverters with data cable In progress Volty Pro On and off via the remote switch connector already works today, see below

Votronic tank level senders, for example the 15-50k, are not integrated. For your tanks, use the sensors from Fluidy.

Ective

Manufacturer Model/series Status Via What works
Ective LC batteries with CAN, for example LC-S and NaC Supported Volty Pro (CAN, with the Victron VE.CAN to BMS Type A cable) State of charge, voltage, current and further data from the BMS
Ective CSI PA PRO inverter/charger Supported Volty Pro (CAN) Read values and fault messages, on and off, limit the mains input current from 1 to 16A
Ective DC-DC chargers and solar charge controllers with CAN Supported Volty Pro (CAN) Read values
Ective Triple (new generation) In progress Volty Pro The integration is being developed

With Ective, only devices with a CAN interface have a data connection. Models without an interface cannot be read.

EcoFlow

Manufacturer Model/series Status Via What works
EcoFlow Power Kit and Power Hub with EcoFlow Power Link Beta Volty Pro (CAN, dedicated connection cable) Battery, solar, DC-DC charger and inverter as separate widgets, switch the outputs of the distribution panel, detect shore power

Without the EcoFlow Power Link, the Power Kit does not share any data. Through EcoFlow, Volty Pro detects whether shore power is present. Only Switchy, however, detects swapped conductors or a missing protective earth.

Other batteries and BMS

Manufacturer Model/series Status Via What works
Bulltron Lithium batteries In progress Volty Pro Integration planned
Daly, JK, JBD Smart BMS In progress Volty Pro The integration is being developed

Your battery is not on the list? You still get the important values: a battery monitor such as the Victron SmartShunt sits on the negative terminal and measures everything that flows in and out. Volty Pro reads it directly. How this fits together is explained in Monitor camper battery and solar.

Devices without a data interface, and shore power

Manufacturer Model/series Status Via What works
All manufacturers Inverters with a remote switch connector (Remote On/Off) Supported Volty Pro (signal relay) On and off from the dashboard and the SmartKnob
All manufacturers 230V shore power connection Supported Switchy Detect shore power, detect swapped live and neutral and a missing protective earth, automation when you plug in
All manufacturers 230V devices up to 10A, for example a charger with Bluetooth only Supported Switchy On and off
All manufacturers 12V and 24V loads Supported Ampy Switch, measure consumption per output, protect electronically

How Switchy checks shore power is explained in What the AC input monitoring does. How Ampy measures your consumption is covered in Measuring power consumption with Ampy and planning off-grid time.

No guarantee is given for this information. The range of functions may differ depending on device generation, firmware and interface.

Your device is missing?

Then write to us using the contact form. Tell us the manufacturer and exact model name of all energy devices on board, that is battery, battery monitor, solar charge controller, DC-DC charger, mains charger and inverter. We will check which of them can be integrated.

Read more

Related questions

Is a simple voltage display enough for the battery?

For a lead-acid battery at rest it gives you a rough idea. For lithium batteries, and for decisions like “will it last until tomorrow?”, it isn't enough, because the voltage hardly changes between about 20% and 90% charge. For that you need a battery monitor or the data from the BMS, which Volty Pro shows you on the SmartKnob.

Do I have to replace my existing power devices?

No. Volty Pro reads your existing devices through their interfaces, and the right cables are included. Whether your device is already supported is shown in the power compatibility list in the knowledge hub.

What can Volty Pro read?

Volty Pro brings your whole energy system together in one place. It reads battery monitors, lithium batteries with CAN, solar charge controllers, chargers, inverter/chargers and DC-DC chargers (battery-to-battery chargers). It connects through each manufacturer's data ports: • Victron via VE.Direct and VE.Bus • Ective via CAN • EcoFlow via the EcoFlow Power Link (Beta) • Votronic via LIN We are working on smart BMS such as Daly, JK or JBD. Which devices already work today is shown in the [Energy compatibility list](/blogs/wissen/kompatibilitaet-energie). Instead of a separate app or display for every device, you see state of charge, solar yield and consumption together on the SmartKnob and in the dashboard, even with a mix of many manufacturers. So you can pick the best from each manufacturer and still have everything in one place.

Do I have to buy the data cables separately?

No, Volty Pro comes with a ready-made cable set for all data ports, included in the box. You do not need to buy anything separately. Only where a manufacturer such as Victron or Votronic specifies its own original communication cable do you use that one, because it is part of the connection the manufacturer has specified.

Can Volty monitor a second battery?

Yes, the second voltage input (Battery 2) lets you keep an eye on an additional leisure battery. Important: this input is intended exclusively for additional leisure or house batteries, not for the starter battery or the vehicle's primary electrical system. That is outside the product specification.

Can I switch my inverter on and off via Volty?

Yes, if your inverter has a remote on/off connection or switching on and off is built into its data interface, as with the Victron MultiPlus or the Ective CSI Pro, for example. Volty Pro has a 2-pin remote output for this. It lets you switch the inverter on and off directly from the dashboard or the SmartKnob, without getting up.

See all questions

Still have questions? We'll help you personally.

Get in touch